Structural steel industry applications

Teach-Free Welding Solutions for Crane Runway Beams

Application solution: assess the welding scope, equipment configuration and acceptance criteria using your crane runway beam drawings and production requirements.

WeldVanta uses a BOCHU system and can take on teach-free welding projects for structural steel such as crane runway beams. We start from your drawings, weld requirements and production conditions, then assess a suitable robot setup, fixture layout and welding flow.

Diagram of a crane runway beam with flange plates, web, stiffeners, end plate and the crane rail on the top flange.123456
Diagram Schematic of a welded H-section crane runway beam, showing the rail, flange plates, web, stiffeners and an end plate. This is an illustration, not a photograph of an installation.
  1. 1Crane rail on the top flange
  2. 2Top flange plate
  3. 3Web
  4. 4Bottom flange plate
  5. 5Stiffener
  6. 6End plate

Crane runway beam sizes change often, and stiffeners and connection plates are not in the same place on every beam. A shop considering a robot usually needs to know more than whether the machine can strike an arc: how long a different beam takes to prepare, what happens when the workpiece is off position, and which manual work remains after the robot welds.

Teach-free welding is meant to reduce the repeated work of recording a path point by point. During selection we assess weld recognition, torch access, fit-up quality and the full production cycle together, rather than choosing a cell from one clip of automatic welding.

Which areas of a crane runway beam should be assessed for automation first?

A crane runway beam is the structural member that supports the rail on which the crane travels. On a common welded H-section, the top and bottom are flange plates, the center is the web, and some locations also have stiffeners, an end plate or connection plates.

Welds in these areas ask different things of a robot.

Areas of a crane runway beam to assess before automating
Weld areaMain characteristicWhat the proposal should check
Web-to-flange connectionOften a long weldWelding position, beam length, equipment travel, procedure requirements and any existing long-seam welder
Stiffener-to-web and stiffener-to-flange connectionsMany short welds and frequent posture changesStiffener spacing, corner clearance, and whether the torch and sensor can enter
End plates and connection platesWeld directions vary and access may be blockedFixture position, welding sequence, the need to turn the beam, and collision space
Other local attachmentsThe structure can change from one order to the nextDrawing preparation, recognition method, changeover flow and the manual work that remains

Joint type, weld size and inspection requirements follow the workpiece drawing. If the shop already has a proven automatic welder for long straight seams, that process can stay. The robot assessment can then focus on the value of welding stiffeners, end plates and similar areas.

Diagram marking weld locations between the web and flange plates, around stiffeners, and at the end plate of a crane runway beam.123
Diagram Schematic weld locations: web-to-flange welds, stiffener welds, and the end-plate connection. Joint type and weld size follow the drawing. This is an illustration, not a field photograph.
  1. 1Web-to-flange weld
  2. 2Stiffener-to-web and stiffener-to-flange welds
  3. 3End-plate weld

How does a BOCHU system reduce repeated teaching?

Conventional robot teaching usually means an operator brings the torch to specified points and records the route point by point. A new structure or size may require a new program, posture corrections and a collision check.

A WeldVanta proposal uses a BOCHU system and organizes the work around workpiece information, weld locating and path generation. In practical terms, the system first gets to know the workpiece, then confirms where the workpiece actually sits, and then arranges for the robot to weld in a suitable posture.

During a project assessment we confirm the following.

  • How workpiece information is entered: whether the available two-dimensional drawings, three-dimensional model or scan data meet the selected configuration.
  • How welds are located: which locating or seam-finding method fits the structure, surface condition and consistency of the fit-up.
  • How the path is executed: torch angle, arm travel and the space between the beam, fixtures and sensors.
  • How the welding procedure is applied: turning material, joint, weld size and quality requirements into procedure settings that have been verified.

The actual functions depend on the selected BOCHU system model, software version, sensors and supporting equipment. Teach-free welding can reduce point-by-point programming, but workpiece preparation, procedure confirmation and inspection by people are still required. Do not assume that every configuration can scan without a model or track every type of weld.

WeldVanta uses a BOCHU welding system as the basis for the solution. We assess the system configuration, supporting equipment and integration scope against your workpiece and production requirements.

How does a proposal move from the drawing to welding?

Diagram of the five-step assessment flow for a BOCHU-based crane runway beam welding proposal.12345
Diagram Assessment flow for a BOCHU-based teach-free proposal: define the welds, plan fixturing, locate and plan the path, confirm the procedure on a sample, then accept the whole beam. This is an illustration, not a photograph.
  1. 1Decide what will be welded
  2. 2Plan assembly, tacking and fixturing
  3. 3Confirm the real position and plan the path
  4. 4Confirm the welding procedure on a sample
  5. 5Accept the result on the whole beam

1. Decide what will be welded

Choose one or two representative crane runway beams and mark weld locations, plate thickness, joint type and quality requirements. Define the automatic range before discussing equipment, so welds that are hard to reach are not discovered only after installation.

2. Plan assembly, tacking and fixturing

The workpiece needs stable support. Fixtures should limit unwanted movement and still leave an entry path for the torch and the sensor. Tack locations, clamping, the turning sequence and welding distortion all belong in the assessment.

3. Confirm the real position and plan the path

The actual placement can differ from the model. A suitable seam-finding setup can confirm the real weld position, and then torch posture, travel range and collision risk can be checked. Whether vision can recognize the joint and whether the torch can reach it should be verified separately.

4. Confirm the welding procedure on a sample

Set the procedure from the welding procedure specification (WPS) and the quality requirements that apply to the project. For multi-layer, multi-pass welds, also confirm bead order, interpass cleaning, temperature control and recovery from an abnormal stop. Real-time tracking should be used only when the configuration and the joint call for it.

5. Accept the result on the whole beam

The record should include loading and unloading, locating, scanning, turning, cleaning and manual repair, not only arc-on time. Weld appearance, size, distortion of the member and any required inspection should be confirmed together with the full cycle time.

If the workpiece varies, can the robot handle it automatically?

A change in position is not the same thing as an unacceptable joint.

The position has shifted. The whole workpiece sits differently, but the joint is still inside the allowed range. A suitable locating or seam-finding setup can help correct the welding position. The actual capability has to be confirmed on the real workpiece.

The joint is out of tolerance. The gap, mismatch or groove shape is outside the procedure limit. Moving the torch to the right place does not by itself produce an acceptable weld. The assembly may need to be redone, the procedure adjusted, or the part repaired.

An assessment should therefore confirm the allowed deviation, how an exception is indicated, and how a person steps in. A workpiece that cannot be recognized reliably, or that is outside the procedure range, should not be welded merely to keep the cell running.

Four checks that matter more than the robot brand alone

Which welds can actually be covered

State which areas can be completed automatically with a stable result, and which manual work remains. Counting welds, measuring length and counting labor hours can give different results. Compare proposals with the same measure. Weld coverage is not the same as the weld acceptance rate.

Whether length, weight and space match

A long beam may need a floor track, a gantry or another external axis. Turning, the lifting route, support points and shop aisles also affect the layout. Arm reach alone does not show that the whole cell is suitable.

Whether the quality requirement can be met consistently

A crane runway beam should be welded to the design and project requirements. Areas with a fatigue requirement especially need the corresponding procedure and inspection. A tidy weld surface does not replace confirmation of fusion, penetration, size and the specified tests.

Whether operation, maintenance and safety are practical

Operators still load and unload, change consumables, maintain the torch, handle exceptions and inspect. The cell needs guarding, fume extraction, emergency stops and safety interlocks that match the layout. Teach-free welding does not mean a person may enter the working area while the robot is moving.

Which configurations can WeldVanta discuss with you?

We can take on teach-free welding projects for structural steel and discuss these points against the actual workpiece.

  • BOCHU system model and the functions that fit the project.
  • Robot working range and external motion such as a floor track or gantry.
  • Matching of the welding equipment, torch and seam-finding or tracking setup.
  • Workpiece supports, fixtures, turning method and the load and unload flow.
  • Procedure verification, the operating sequence and what the project acceptance will check.

The configuration should serve the specific workpiece and the output target. The final scope of supply, function options and acceptance criteria are those agreed in the technical proposal.

Send this information to start assessing your project

A preliminary discussion can start from photos, two-dimensional drawings and the main dimensions even when a complete three-dimensional model is not available yet.

Information that helps the first assessment
InformationWhat is useful to send
Drawings or photosOverall workpiece, weld callouts, and stiffener and end-plate details
Size and weightBeam length, beam depth, flange width, plate thickness and the weight of one piece
Material and welding requirementsMaterial, joint type, weld size, penetration and inspection requirements
Production planOutput per shift or per month, product variety and changeover frequency
Current production conditionsPower source, wire, shielding gas, available space and lifting method
What you want to improveRepeated teaching, manual repair, workpiece variation, cycle time or operator workload

Tell WeldVanta what you are welding and which step takes the most labor. We can sort out which operations are realistic to automate.

Discuss Your Crane Beam Welding Project

To discuss drawings or shop photos, start with WhatsApp contact with WeldVanta. Describe the workpiece use and what should be assessed, then confirm a suitable way to send files. If you use the website form, an outline of the workpiece is enough to begin.

WhatsApp: 19563468158

Phone: +86 19563468158

Common questions

Does teach-free mean operators need no robot experience?

It can reduce point-by-point programming, but operators still need training in workpiece preparation, task checks, maintenance and recovery from an abnormal stop. The people who will run the cell should take part in the sample trial.

Can one cell be shared when every batch of crane runway beams has a different size?

That depends on the size range, the structural change, the robot travel and the system configuration. A size change within a similar structure does not need the same preparation as adding a completely different structure.

Can a BOCHU system automatically weld every area?

The system brand alone cannot answer that. Obstruction, fixtures, torch angle, sensor space and the need to turn the beam all affect access. The proposal should state the robot’s working range and the operations that remain manual.

Can we inquire with only two-dimensional drawings?

Yes. Drawings, photos, dimensions and welding requirements are enough for a preliminary assessment. The model or scan data required for production running should be confirmed for the configuration that is finally selected.

Can you promise a fixed productivity gain or payback period?

A calculation needs the current labor time, output, labor cost, equipment configuration and sample-test results. Workpieces and production schedules differ, so the estimate should use this project’s own data.

Can this approach be used on other structural steel?

It can be a starting point for the assessment. Other beams, columns or stiffened members need their own check of structure, welds, locating method, access and quality requirements. A crane runway beam configuration should not be copied across unchanged.

Related pages

Start with an outline of the workpiece

Describe the workpiece, the weld requirements and the target output. How to send drawings can be confirmed afterward. This form does not upload files.

Contact

The form is loading. If it does not become available, you can contact us on WhatsApp.